對講機進水后，一定不能上電開機！先拆開機器外殼，小心取出機板，用專用洗板水將線路板仔細清洗干凈、晾干，用細小毛刷清理干凈電路板上的污漬；有條件可用超聲波清洗機進行清洗；其次撈出后用電吹風吹干（注意溫度不可過高），清理干凈水份后，通過儀器檢測各項指標是否正常，如有其它故障再按常規方法進行檢修。沈陽對講機哪家好你知道嗎？

沈陽對講機從軟件方面去排除，是否為參數設置問題。解決方法：把相同型號、頻段的機器讀出參數，然后直接寫入到故障機，看能否解決。

機器硬件問題：拆機后用萬用表測TP點（即VCO電壓測試點）無鎖定電壓，試調C180，該點電壓無變化，再測震蕩管Ｑ14各極都無電壓， 據此可知Ｑ14沒有振蕩。懷疑是電源電路有問題，檢測為鎖相環路提供電源的Q32無5V電壓輸出，更換Q32故障排除。

對電路腐蝕嚴重的進水機一般都無法修復，因此機器進水后應進行及時處置，不然，就會腐蝕機板造成無法修復。

沈陽對講機可充電鋰離子電池已在對講機中廣泛，在使用中不可過充、過放(會損壞電池或使之報廢)。因此，在電池上有保護元器件或保護電路以防止昂貴的電池損壞。（冒牌劣質產品多數沒有該保護電路） 鋰離子電池充電要求很高，要保證終止電壓精度在1%之內，目前各大半導體器件廠開發出多種鋰離子電池充電的ic，以保證可靠、快速地充電。

鋰離子電池不適合用作大電流放電，過大電流放電時會降低放電時間(內部會產生較高的溫度而損耗能量)。因此電池生產工廠給出大放電電流，在使用中應小于大放電電流。 鋰離子電池對溫度有一定要求，工廠給出了充電溫度范圍、放電溫度范圍及保存溫度范圍。

文章內容來源于網絡，如有問題，請與我們聯系！